by Regardt Voigt | Jul 24, 2022
ASCII data – which is used to be scanned into a SCADA system as a string, can be stored in both Binary string (16-Bits) or Hexadecimal format, inside of an D register.
by Regardt Voigt | Jun 11, 2021
This tool is for setting up the Ethernet/IP Communication Protocol on FX5. This tool can be downloaded here: FX5ENET-IP Configuration Tool 1.00 (note that a username and password will be required – therefore registration of an account will be required. This...
by Regardt Voigt | Jun 11, 2021
It is possible by setting the scaling function or shift function from the parameter settings
by Regardt Voigt | Jun 11, 2021
Up to 4 high-speed pulse input/output modules FX5-16ET/ES-H，FX5-16ET/ESS-H* can be expanded, allowing a total of 16ch input (including built-in high-speed counter) ＊：High speed counter function of FX5-16ET/E□-H is equipped with 2ch
by Regardt Voigt | Jun 11, 2021
The high-speed counter supports 1-phase 1-input, 1-phase 2-input, 2-phase 2-input. The built-in counter in the CPU module can input up to 8ch. However, in the case of 32 point type CPU module, the maximum response frequency differs depending on the channel. –...
by Regardt Voigt | Jun 11, 2021
Yes, it is possible. Please consider functions such as socket communication or SLMP communication function.
by Regardt Voigt | Jun 11, 2021
Up to 4 axes can be controlled. Please use a transistor output type CPU module. （By adding a high-speed pulse input/output module, maximum 12 axes (CPU built-in 4 axes＋expansion 2 axes×4 modules） can be configured.
by Regardt Voigt | Jun 11, 2021
It can be changed. For details, please refer to MELSEC iQ-F FX5 User’s Manual (Positioning Control – CPU module built-in, high-speed pulse input/output module) 3.4 Auxiliary Functions “Command speed change during positioning...
by Regardt Voigt | Jun 11, 2021
It can be changed. For example, with the positioning instruction, a word device can be assigned to the operand which specifies the positioning address and the address can be changed by rewriting the value.
by Regardt Voigt | Jun 11, 2021
Device backup is available without using a battery. However, to back up link register (W) and file register (R) devices, a battery is required.
by Regardt Voigt | Jun 11, 2021
Ethernet standard-compatible cable, category 5 (CAT5) or higher (STP cable) can be used. *Straight cable can be used. When connecting directly to the computer, a cross-over cable can also be used.
by Regardt Voigt | Jun 11, 2021
The current value of the scan time is stored in the following special devices. Please monitor using GX Works3. ◇Scan information SD520 Current scan time (ms) SD521 Current scan time (μs) ◇FX Compatible area SD8010 Current scan...
by Regardt Voigt | Jun 11, 2021
FX3U-32BL can be used. The battery is not included with the CPU module during factory shipment. The battery can be used to increase the capacity of the latch device/label, as well as to maintain the clock data during power interruption.
by Regardt Voigt | Jun 10, 2021
32 stations can be connected when RS-485 port is used and only 1 station can be connected when RS-232 port is used.
by Regardt Voigt | Jun 10, 2021
N;N Network, Parallel Link, MELSEC Communication protocol, Non-protocol communication, MELSOFT connection, MODBUS/RTU, and Predefined protocol support are available.
by Regardt Voigt | Jun 9, 2021
The connection using the Ethernet port can establish a total of 8 connections which includes SLMP, MELSOFT connection, MODBUS/TCP, socket communication, and predefined protocol support function. The first of MELSOFT(connection with GX Works3) connection, CC-Link IE...
by Regardt Voigt | Jun 9, 2021
The FX5 CPU module does not support UDP broadcast communication.
by Regardt Voigt | Jun 9, 2021
The settings can be done using the parameter settings of GX Works3 or by settings the special relay/special registers. For further details please refer to MELSEC iQ-F FX5 User’s Manual (CPU Module Built-In Analog/Expansion-Adapter）. 6 FX5U CPU MODULE BUILT-IN...
by Regardt Voigt | Jun 9, 2021
Multiple connections can be established by using an Ethernet switching hub.
by Regardt Voigt | Jun 4, 2021
The wiring of an FX5 PLC includes the Digital Discrete Inputs\outputs and the Analog Continuous Inputs\Outputs. In addition, this includes the wiring of the RS-485 serial communication port on the PLC. The MELSEC iQ-F FX5U User’s Manual (Hardware) describes...
