by Regardt Voigt | Jun 11, 2021
It can be changed. For details, please refer to MELSEC iQ-F FX5 User’s Manual (Positioning Control – CPU module built-in, high-speed pulse input/output module) 3.4 Auxiliary Functions “Command speed change during positioning...
by Regardt Voigt | Jun 11, 2021
The execution time of the basic operation instruction(LD) is 0.034[μs]. *For firmware Ver.1.100 or above, this specification applies to 64K step mode.
by Regardt Voigt | Jun 10, 2021
Yes, CW/CCW outputs are supported. Up to 2 axes can be controlled by setting parameters from GX Works3. Also, by adding a high-speed pulse input/output module, up to 8 axes can be added.
by Regardt Voigt | Jun 10, 2021
GX Developer/GX Works2 cannot be used. MELSEC iQ-F series only supports GX Works3.
by Regardt Voigt | Jun 9, 2021
From the Microsoft? Windows?7’s Internet Protocol Version 4 Properties, uncheck “Obtain an IP address automatically” option and set an arbitrary IP address that does not duplicate with the address of MELSEC iQ-F. Also, if the subnet mask is...
by Regardt Voigt | Jun 9, 2021
The settings can be done using the parameter settings of GX Works3 or by settings the special relay/special registers. For further details please refer to MELSEC iQ-F FX5 User’s Manual (CPU Module Built-In Analog/Expansion-Adapter）. 6 FX5U CPU MODULE BUILT-IN...
by Regardt Voigt | Jun 9, 2021
From the following menu of GX Works3: [Diagnostics]→[Module Diagnostics(CPU Diagsnostic)] the event history function can be found. The event history can display the error information of the CPU module, expansion board, expansion adapter, and network. Also, the...
by Regardt Voigt | Jun 9, 2021
The settings can be done using the parameter settings of GX Works3 or by settings the special relay/special registers. For further details please refer to MELSEC iQ-F FX5 User’s Manual (CPU Module Built-In Analog/Expansion-Adapter）. 6 FX5U CPU MODULE BUILT-IN...
by Regardt Voigt | Jun 9, 2021
Parameters can be set when connecting the MELSEC iQ-F series with FX5-CCL-MS (CC-Link system master/intelligent device). However, when connecting with FX3U-16CCL-M(CC-Link master), the settings must be configured using a program. For further details, please refer to...
by Regardt Voigt | Jun 9, 2021
Multiple connections can be established by using an Ethernet switching hub.
by Regardt Voigt | Jun 5, 2021
A good description of the Melsec iQ-F PLC series can be found HERE.
by Regardt Voigt | Jun 5, 2021
There are 3 main types of Melsec iQ-F CPUs, namely FX5U, FX5UC, and FX5UJ. Their differences\Specifications can be found HERE.
by Regardt Voigt | Jun 5, 2021
The Melsec iQ-F’s advanced features are summarized HERE.
by Regardt Voigt | Jun 5, 2021
The following website provides the basic breakdown of the products that are available: Melsec iQ-F Series
by Regardt Voigt | Jun 4, 2021
The wiring of an FX5 PLC includes the Digital Discrete Inputs\outputs and the Analog Continuous Inputs\Outputs. In addition, this includes the wiring of the RS-485 serial communication port on the PLC. The MELSEC iQ-F FX5U User’s Manual (Hardware) describes...
by Regardt Voigt | Jun 4, 2021
The following manual is specifically intended for that purpose: MELSEC iQ-F FX5 User’s Manual (Analog Control – Intelligent function module). It can be accessed here.
by Regardt Voigt | Jun 1, 2021
The Melsec-iQ-F PLC comes in three flavours: FX5U (Standard), FX5UC (Compact) and FX5UJ (Junior). The FX5U is programmed with an Ethernet cable. The FX5UJ can be programmed with either a mini-USB or Ethernet cable. The FX5UC is programmed with an Ethernet cable....
by Regardt Voigt | Jun 1, 2021
GX Works3 – Additional training resources: Some information upon which these courses are based are: (Melsec-iQ-F): Melsec iQ-F Intermediate: FX5 User’s Manual (Startup) Melsec-iQ-F Advanced: FX5 Programming Manual (Program Design)
