by Regardt Voigt | Mar 27, 2019 | FR-A7xx, FR-A8xx, FR-CS8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, VSD
Choosing The Right Drive For The Right Application Introduction When choosing the correct Inverter drive for the correct application, we don’t always know which Inverter to use. The following is a guideline to help you with this choice: FR-A800 series Modular...
by Regardt Voigt | Mar 23, 2018 | FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, VSD
Introduction FR-E700 Inverter error codes can be found under troubleshooting section of the manual (attached). This section looks specifically at the Fault 7 based drive failure. Error E.7 Details As can be seen this error is related to electrical noise, external the...
by Regardt Voigt | Mar 21, 2018 | FR Configurator, FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, VSD
Read and export 700 series inverter Parameterization information Introduction It is often a requirement to document and record all the information available within an inverter but the question has often been how? Using the Mitsubishi FR Configurator software, the...
by Regardt Voigt | Mar 19, 2018 | FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, VSD
All 700 series inverter drives have I/O and it is now possible to monitor all I/O states from the parameter unit. Introduction Mitsubishi inverter drives have always had digital inputs and outputs (I/O), but has not always been possible to monitor the status of these...
by Regardt Voigt | Mar 17, 2018 | FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, VSD
All Mitsubishi inverters need the same basic setup as detailed below. Introduction All Mitsubishi inverters require a basic minimum setup. This basic setup is needed to match the inverter to the motor and to the application. In simple terms there are 9 – 10 basic...
by Regardt Voigt | Mar 6, 2018 | FR Configurator, FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, PID Control, VSD
Introduction The following is a short and practical description on how to setup VSD PID control via a FR-E700 inverter. Inverter Wiring Requirements; Inverter PID Control Parameterization: Reference Material For the FR-E700 applied manual – for reference...
by Regardt Voigt | Mar 6, 2018 | FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, VSD
Introduction All 700-Series inverters support a feature that displays information/error codes on the parameter unit. These display messages give information about the inverter and its status but are not alarm messages. Design Considerations An example of a non-alarm...
by Regardt Voigt | Mar 5, 2018 | FR Configurator, FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, Software, VSD
Introduction Normally VSDs are tested through the control of the parameter unit or external controls. FR-Configurator software gives another alternative for testing. Design Considerations A 700 series VSD can be controlled by the FR-Configurator software by following...
by Regardt Voigt | Mar 5, 2018 | FR-A7xx, FR-A8xx, FR-D7xx, FR-E7xx, FR-F7xx, FR-F8xx, GOT HMI, GOT1000, GT2000, VSD
Introduction The GT1000 range of GOT/HMIs have a driver that supports connection to the 500 and 700 series Mitsubishi Electric VSDs. This provides the ability to interact with the VSD data and display information such as alarm codes. When displaying alarm codes the...
by Regardt Voigt | Feb 28, 2018 | FR-E7xx, FR-F7xx, FR-F8xx, VSD
Introduction Where several motors are to be speed controlled at the same speed it can be an efficient solution to install one suitably rated VSD drive to control these motors. Design Considerations The following points need to be considered in the design and...
